1. Confirmation of water pipe direction and positioning of water equipment:
The customer has more decoration design drawings and room type structure to determine the direction of the water pipe. The direction of the water pipe can be divided into ceiling arrangement, wall slot arrangement, floor arrangement and clear pipe installation. Which way to choose is negotiated with the decoration.
| Ceiling arrangement | Wall slot arrangement | Ground arrangement | Tube installation |
â— In general, the principle of water pipe grooving is “walking without walking, not going horizontallyâ€.
â—‹Because there are many buried pipes and wires underground in the planed ground, it would be very troublesome to destroy the original underground pipes! If you go to the ground, in the event of a late-stage renovation, if the electric drill breaks the water pipe, it will affect safety!
â—‹ It is not easy to find the waterway because the water is flowing down. The leaking area does not have to flow out first. Only when the water leaks downstairs or into the flood plain, water leakage will be discovered. However, because it is a dark pipe, it cannot Immediately find the leaking place, so the loss will be quite large; if you go to the top, the kitchen bathroom can be covered with aluminum buckle ceiling, in the entrance through the entrance section we are walking along the corner, you can use the plaster line, does not affect Beautiful.
â—‹ When the water pipe leads to the bathroom and meets the place where you need water, go down the vertical slot to a suitable height and reserve a shower, wash basin, washing machine and other water outlets. The advantage of doing this is that, when the decoration is finished tiling, you can judge the direction of the water pipe according to the location of the outlet. All the water pipes are vertically upward at the water outlet, so as to prevent the water pipes from being damaged for any reason and leaking water for easy maintenance.
â— When designing a waterway, pay attention to:
â—‹ The waterway design must first consider all equipment related to water, such as water purifiers, water heaters, kitchen treasures, toilets and wash basins, etc. Their location, installation methods, and whether they need hot water, or whether they want to use gas or electricity in advance. Water heaters, to avoid temporary replacement of water heaters, leading to repeated changes in the waterway â—‹ In addition to leaving the bathroom sinks, toilets, washing machines and other outlets, it is best to pick them up, then pick up the water to the ground and so very convenient; this depends on the owners Everyone likes the problem â—‹After the location of the washing machine is determined, the drainage of the washing machine can be considered to be inside the wall of the drainage pipe, beautiful and convenient
2, grooving process specification:
1 When the communication with the construction staff is good, the water will begin construction. First draw a line of ink to outline the route you need to take the tube (you can see from the road map that it is horizontal and vertical, this time if you have different opinions or changes, you can also discuss with the worker's master). These preparatory work is about an hour or so.
2 After playing a good line, it is to open the dark trough, use a special tool cutting machine to cut the groove surface according to the line, and then use a hammer to slot. In addition, it needs to be reminded that some residential areas are heavy and thick steel bearing wall, can not be rebar Cut off (affect the quality of the house), only open shallow (need to thicken the cement when tiling) or walk out of the tube, or bypass other walls.
3, slotting construction size requirements:
The width of the wall groove is 4cm for a single groove, 10cm for a double groove, and 3-4cm for a wall groove. And pay attention to horizontal and vertical. The height of the gutter is based on the different equipment used.
| Water equipment export | Targeting regular height | Water equipment export | Targeting regular height | Water equipment export | Targeting regular height |
| Table hot and cold water height | 55cm | Wall outlet plate height | 95cm | Mop pool height | 60-75cm |
Standard bathtub height hot and cold water center distance | 75cm | Shower height hot and cold water center distance | 100-110cm | Jacuzzi height | 30cm |
| Water heater height (gas) Water heater height (electric heating) | 130-140cm 170-190cm | Small washing machine height standard washing machine height | 85cm | Toilet height squat height | 15cm 100-110cm |
| The above is the normal size, which is calculated after the indoor floor is laid. If there are special circumstances, the actual equipment shall prevail. | |||||
There must be a space between hot and cold water pipes. Because the hot water is heated by the water heater, the heat is lost during the cycle. If hot and cold water pipes are close together, cold water is also circulated, and the hot water pipes are also very hotly lost.
Through the hole size requirements: If the diameter of a single water pipe wall hole is 6cm, if you take two water pipe hole diameter 10cm or hit two 6cm diameter wall hole to walk away.
Hydroelectric reform toilet interior decoration decoration cement bathroom decoration design kitchen bathroom ceiling bathroom size bathroom design bathroom ceiling bathroom vanity bathroom design bathroom leak
Concrete Admixture Co., Ltd. , http://www.wxchemicals.com