The summer is about to take place, and the bathroom is the place with the largest amount of water in the family. In the summer, it is like a flood of water, causing a flood crisis. For bathrooms that have no windows and are poorly ventilated, the moisture can cause mold, deformation, and even wall tile detachment in the bathroom tiles. Pick up from the purchase, teach you the knowledge of bathroom tiles.
Bathroom tile purchase must be waterproof and wearable
The bathroom usually has a relatively high humidity, and the requirements for the tile are waterproof, slip resistant and wear resistant. The bathroom floor tiles are generally made of whole body bricks, which have good non-slip wear resistance. The bathroom wall tiles are usually made of glazed tiles. The glazed tiles are glazed and processed with rich color patterns and strong anti-fouling ability.
Bathroom tile purchase to see the water absorption rate of the tile
Tiles for the purchase of bathroom space should first pay attention to its water absorption rate. In general, high quality tiles have a low water absorption rate so they can dry quickly. If the tile does not indicate the water absorption rate, you can use tea or water droplets on the back of the tile. After a few minutes, the degree of diffusion of the water droplets is observed. The less water is absorbed, the lower the water absorption rate and the better the quality.
Bathroom tile purchase to see the brick surface glaze degree to prevent mildew
When purchasing, it can be identified by judging the thickness of the glaze on the tile surface. The surface of the brick can be scraped with a hard object, and if a scratch occurs, it means that the glaze is insufficient. After the thinner glaze layer on the tile surface is polished, the brick surface is easily stained, difficult to clean, and lacks safety. Some unglazed floor tiles are generally not suitable for being placed in a damp and closed environment. Because the pores on the bricks absorb water and cannot diverge, they can also cause mold.
Tile anti-deformation must be soaked in bathroom tile decoration
Due to the dampness of the bathroom, in order to prevent the tiles from being deformed after being absorbed by water, the tiles should be soaked in water before tiling. The different tiles have different densities and the time required is different (30 minutes to 12 hours, soaked until no Bubbles are appropriate, and the color of the tiles filled with water will be more uniform). Cement mortar is used as the bonding layer for laying ceramic tiles. Cement mortar should be selected more evenly. No agglomeration is good, and thick and thick is appropriate to avoid the mortar flowing down or the unevenness of bonding during the laying process.
When the bathroom tile is decorated, the tile must have no gap to prevent it from falling off.
Pull the horizontal and vertical lines on the wall to make the tiles flat and bottom-up. The bottom tiles should not be close to the ground, leaving room for the tiles. In order to ensure the adhesion of the tile, first make sure the back of the tile is cleaned and then apply the mortar, and paste the tile according to the horizontal and vertical lines. After sticking it, gently tap it with a rubber hammer to ensure that the middle and the four corners are completely bonded to the wall surface, and there is no gap. This is also an important step in the construction of the wall brick. If there is a gap, the water easily erodes from the inside, causing damage to the tile.
How to clean the bathroom tiles against mold
1, the daily cleaning of tiles can be washed with detergent, soap and so on.
2. Contaminants such as hydrochloric acid and nitric acid are used as pollutants in ink and cement.
3. Special cleaning agents for paints, paints and other pollutants.
4. High-quality tiles can be cleaned with cloth and water. Use as little or no other chemicals as possible.
5, add a little ammonia and turpentine mixture with soap, clean the tiles to make the tiles more shiny.
How to maintain the bathroom tiles against mold and color loss
1. Polished bricks should be waxed regularly, with a time interval of 2-3 months.
2. If there is a scratch on the brick surface, apply the toothpaste on the scratched surface and wipe it with a dry cloth to repair it.
3, bricks and bricks can be used occasionally with decontamination paste to remove dirt, and then a layer of waterproofing agent in the gap, can prevent mold growth.
The modern family bathroom is generally tiled, which just pays attention to the immunity of the tile to the special space of the bathroom. Therefore, in order to make our bathroom last for a long time, we can do enough homework for the bathroom tile. I hope to provide a reference for the majority of families to decorate the bathroom.
Drill Accessories,Double Ended Screwdriver Bits,Electric Drill Screwdriver Bits,Screwdriver Bits
Danyang Yongshun Tools Co.,Ltd , https://www.china-drill-bit.com